Learn / Lesson 01
Lesson 01 · 10 minutes
The machine is a system
Before touching a program, learn who does what: spindles, turrets, axes and control.
By the end you can describe what the main spindle and the sub-spindle do and follow the part from the first operation to the transfer.
01
The principle: the part spins, the tool shapes it
In turning, the spindle rotates the part and the tool removes material until the shape on the drawing is reached. On a CNC lathe you don’t move the slides with handwheels: the control does it by following the program.
“CNC lathe” covers a very wide family. The number of spindles, turrets, axes and live tools changes from model to model. The first question in front of a new machine is always: how is this one configured?
02
Four units, four jobs
Main spindle: holds the part in the first operation and spins it while that side is machined. Sub-spindle (counter-spindle): an opposed second spindle, only on some machines; it takes the part over to machine the side that was hidden before.
Turret: carries the tools and brings them into position by indexing; on some machines it also carries live (driven) tools. CNC control: reads the program and coordinates everything. Codes and functions change between builders: always check the manual of the control actually installed.
03
Why two spindles
Many parts need machining on both ends. With a sub-spindle the machine can take the part over and finish it without the operator flipping it by hand: fewer manual re-clampings, fewer locating errors.
Careful, though: two spindles don’t make every cycle faster by default. The transfer has to be planned, programmed and checked, and not every machine can cut with two turrets at the same time.
04
Follow the part in four moments
Loading, first operation, transfer, second operation. At each step ask two questions: who is holding the part now? and which surface can I reach? The diagram below walks you through it.
It is a teaching diagram, not a machine cycle: real movements, clamping confirmations and interlocks depend on the machine and the program.
▶
The diagram
?
Think it through: a small shaft to finish on both ends
- Which surfaces can you reach while the part is held in the first operation?
- Which ones are left for after the transfer?
- What do you need to check before treating the part as properly held by the sub-spindle?
There is no single answer: geometry, material, tolerances and machine setup decide the strategy. The exercise trains you to reason in terms of access and workholding instead of copying another part’s sequence.
⚙
A possible sequence (teaching example)
Steel shaft from bar stock, with a collar in the middle and two journals: side B facing out in the first operation, side A towards the spindle.
- OP1 · main spindleFace side B, rough and finish the side B diameters up to the collar, chamfers. The collar shoulder becomes the reference for lengths.
- TransferThe sub-spindle grips the part on the finished journal B (bored soft jaws or a collet, so it isn’t marked), with the collar shoulder against the stop. Then part-off from the bar.
- OP2 · sub-spindleFace side A to overall length, referenced from the shoulder; rough and finish journal A, chamfers.
- InspectionOverall length and collar position from the shoulder, both journal diameters, concentricity between the journals if the drawing calls for it.
An invented example to explain the reasoning: on a real part, workholding, references and operation order depend on the drawing, the material and the machine.
Aa
Words to remember
- Spindle
- spins and clamps the part
- Sub-spindle
- opposed second workholding
- Re-clamping
- holding the part again in a new position
- Turret
- carries and changes the tools
- Axis
- a controlled movement
- Synchronisation
- two units working in step
✓
Test yourself
Three quick questions. Get them all right and the lesson is marked as completed on this device.
What does the sub-spindle do?
Do two spindles always make the cycle faster?
In front of a new machine, what should you understand first?
Lesson completed.
≡
Take it to the shop floor
- Main spindle and sub-spindle are two possible ways of holding the part.
- The sub-spindle makes surfaces reachable that were hidden in the first operation.
- Machine configuration and cycle are always checked on the real machine.
↗
Further reading
Machine builders’ pages are quoted as examples: for your machine, always follow the manual and data sheets of the specific model.